Products

The small incu­ba­tor is designed for warm air incu­ba­tion and gassing in com­bi­na­tion with a Heat­ing Insert and is suit­able for high-resolution microscopy. The heat­ed glass of the incu­ba­tor has a translu­cence of about 90% for light in the visu­al wave­length range, warm­ing up the incu­ba­tion cham­ber from the top. The abbre­vi­a­tion RBT stands for Rapid Balanced Temper­a­ture. Incu­ba­tor PM 2000 RBT replaces Incu­ba­tor PM 2000 and Incu­ba­tor PM S1. To the prod­uct

The large mod­u­lar incu­ba­tor (basic hous­ing plus con­fig­urable door sets and slide-in mod­ules) is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass with dim­ma­ble dual LED illu­mi­na­tion, it is designed for the Leica DMi8 invert­ed micros­cope. To the prod­uct

The MODU 2000 Basic Com­po­nent and the user change­able Heat­ed Plates for mul­ti­well plates with 6, 12, 24, 48 or 96 wells with a plane poly­styrene or glass bot­tom heat up spec­i­men up to 60°C. It fits on invert­ed micro­scopes with a scan­ning stage or a mechan­i­cal stage (cut-out 160 x 110 mm). The mul­ti­well plates are heat­ed direct­ly from below with a uni­form heat dis­tri­b­u­tion. Togeth­er with the Incu­ba­tor PM 2000 RBT it is the base for a mul­ti­well stage-top incu­ba­tion sys­tem. To the prod­uct

Flex­i­ble device for the fix­a­tion of var­i­ous cul­ti­va­tion ves­sels and T25 flasks on mechan­i­cal and scan­ning stages (open­ing 160x110 mm) at inverse micro­scopes. It has been specif­i­cal­ly designed for the use of large Petri dish­es with a max­i­mum diam­e­ter of 92 mm and can be installed eas­i­ly. To the prod­uct

The large incu­ba­tor is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass with trans­par­ent doors it is designed for invert­ed micro­scopes by Olym­pus. To the prod­uct

Uni­ver­sal Mount­ing Frame with 5 base­plates for ‘35’,’60′ and ‘100’ Petri dish­es, POC-Systems, Lab-Tek^TM and Ibi­di Cham­bers. The frame fix­es var­i­ous cell cul­ti­va­tion ves­sels on scan­ning and mechan­i­cal stages (open­ing 160x110 mm) on invert­ed micro­scopes and can be installed eas­i­ly. The base­plates togeth­er with the CO₂-Cov­er 100-Set give a closed envi­ron­ment inside a large heat­ed micros­cope incu­ba­tor for local gassing and humid­i­fi­ca­tion. To the prod­uct

The CO₂-Cov­er KM Set fits on the Uni­ver­sal Mount­ing Frame KM with var­i­ous insert plates of the Click-In Sys­tem Pre­mi­um on invert­ed micro­scopes. It allows local gassing of cell cul­tures with CO₂ and / or reduced O₂ and humid­i­fi­ca­tion. Includ­ed are two cov­er vari­ants: Vari­ant 1 with a fixed glass, Vari­ant 2 with slid­able glass plates (e.g. for pipet­ting and micro­ma­nip­u­la­tion) To the prod­uct

Unfor­tu­nate­ly our pop­u­lar pro­ducts Uni­ver­sal Mount­ing Frame KM (and Click-In Sys­tem) and CO₂-Cov­er KM are not com­pat­i­ble to the Stage attach­ment Z PIEZO WSB 500 from Zeiss. In that case use this “Adapter Frame for Uni­ver­sal Mount­ing Frame KM” on top of the Uni­ver­sal Mount­ing Frame KM togeth­er with the CO₂-Cov­er PM / PM S for local CO₂ gassing and humid­i­fi­ca­tion. To the prod­uct

The large laser-safe incu­ba­tor is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass it is designed to meet all laser safe­ty require­ments. To the prod­uct

The Con­trol Sen­sor T 2000 ster­il­iz­able is a small-sized con­trol device for mea­sur­ing the tem­per­a­ture in “60” Petri dish­es. By means of this sen­sor, the actu­al tem­per­a­ture in the medi­um of the cell cul­ti­va­tion ves­sel can be mea­sured in pre-experiments. The whole sen­sor unit (glass cov­er, cable with LEMO® plug, Pt100-sensor) can be ster­il­ized. To the prod­uct

The large incu­ba­tor is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass with trans­par­ent doors it is designed for invert­ed micro­scopes by Olym­pus. To the prod­uct

The Heat­ing Insert UP-Set 2000 is designed for the sta­ble heat­ing of cell cul­ti­va­tion sys­tems on upright micro­scopes above ambi­ent tem­per­a­ture up to 60°C. It can be equipped with a CO₂-Cov­er for local CO₂ con­trol and humid­i­fi­ca­tion. Because of its sol­id design, it has a high tem­per­a­ture con­stan­cy and ther­mal con­duc­tiv­i­ty. Four exchange­able base­plates enable the use of a large num­ber of cell cul­ture sys­tems. To the prod­uct

This Heat­ing Insert is avail­able in sev­er­al vari­ants designed for the sta­ble heat­ing of mul­ti­well plates with 6, 12, 24, 48 or 96 wells with a plane poly­styrene or glass bot­tom up to 60°C. It fits on invert­ed micro­scopes with a scan­ning stage or a mechan­i­cal stage (cut-out 160 x 110 mm). The mul­ti­well plates are heat­ed direct­ly from below with a uni­form heat dis­tri­b­u­tion. Togeth­er with the Incu­ba­tor PM 2000 RBT it is the base for a mul­ti­well stage-top incu­ba­tion sys­tem.
To the Stage Inserts

The CO₂-Con­troller 2000 is a con­trol unit used for the pressure-less sup­ply of small incu­ba­tors on micro­scopes with a con­trolled CO₂ air mix­ture via small gas feed­ing. With the use of cheap tech­ni­cal CO₂ a con­trolled gas mix­ture from 0.0-20.0% CO₂ can be gen­er­at­ed. A Humid­i­fi­er flask is includ­ed. To the prod­uct

The CO₂-O₂-Con­troller 2000 is a con­trol unit for the pressure-less sup­ply of small incu­ba­tors on micro­scopes with a con­trolled CO₂/O₂ air mix­ture via small gas feed­ing. With the use of cheap tech­ni­cal CO₂ and N₂ a con­trolled gas mix­ture from 0.0-20.0% CO₂ and 20.8% - 0.1% O₂ can be gen­er­at­ed. Long last­ing zir­co­ni­um based oxy­gen sen­sor. A large Humid­i­fi­er flask is includ­ed. To the prod­uct

The large light-tight incu­ba­tor is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass it is designed for invert­ed micro­scopes by Olym­pus. To the prod­uct

In Novem­ber 2018 PeCon suc­cess­ful­ly passed the qual­i­ty audit accord­ing to the new ISO stan­dard, which was pub­lished as ISO 9001:2015 on Sep­tem­ber 23, 2015 and replaces the pre­vi­ous ISO 9001:2008. PeCon stands for high prod­uct qual­i­ty and cus­tomer sat­is­fac­tion. All of our pro­ducts are “Made in Ger­many”. To the cer­tifi­cate

This insert is made for the sta­ble heat­ing of many dif­fer­ent cell cul­ture ves­sels up to 60°C. It fits on invert­ed micro­scopes with a scan­ning stage or a mechan­i­cal stage (cut-out 160 x 110 mm). It offers a uni­form heat dis­tri­b­u­tion, a high ther­mal con­duc­tiv­i­ty and is equipped with a heat­ed and slid­able CO₂-Cov­er. Four exchange­able base­plates enable the use of a large num­ber of cell cul­ture sys­tems. Togeth­er with a tem­per­a­ture and a gas con­troller this is a ver­sa­tile stage-top incu­ba­tion sys­tem. To the prod­uct

The light-tight incu­ba­tor for the Axio Observ­er comes with inno­v­a­tive fea­tures: A spa­cious access over the entire front, a mov­able obser­va­tion win­dow, a more com­fort­able han­dling of the lamp sup­port despite mount­ed incu­ba­tor, an easy assem­bly and dis­as­sem­bly due to cable entries in and below the stage, a flex­i­ble adap­ta­tion to dif­fer­ent micros­cope con­fig­u­ra­tions as well as a con­ve­nient inte­riour equip­ment like a humid­i­fi­er bot­tle hold­er and shelves. An addi­tion­al fea­ture is the illu­mi­na­tion of the inte­ri­or which is avail­abe in the vari­ants Stan­dard (on/off) and Pre­mi­um (dim­ma­ble). To the prod­uct

Get the lat­est firmware for our Series 2000 devices and com­po­nents to have new fea­tures, bug­fix­es and full com­pat­i­bil­i­ty of all devices with each oth­er.
To the down­loads

The CO₂-Cov­er 100-Set fits on the Uni­ver­sal Mount­ing Frame K100-Set and M100-Set on invert­ed micro­scopes. It per­mits a local CO₂-con­trol and humid­i­fi­ca­tion in a com­plete­ly closed envi­ron­ment. Usage in a large incu­ba­tor is high­ly rec­om­mend­ed to pre­vent con­den­sa­tion. To the prod­uct

The Click-In Sys­tem is a mul­ti­func­tion­al and flex­i­ble Sys­tem of var­i­ous insert plates for the fix­a­tion of dif­fer­ent cell cul­ture ves­sels on xy-stages and scan­ning stages at inverse micro­scopes. The Uni­ver­sal Mount­ing Frame KM or the Insert AM serve as base frames. To the prod­uct

The large mod­u­lar, laser-safe incu­ba­tor is made for a con­trolled warm air incu­ba­tion and enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents. Con­struct­ed from black acrylic glass and equipped with laser safe­ty inter­locks and dim­ma­ble dual LED illu­mi­na­tion, it is designed for the Leica DMi8 invert­ed micros­cope. The incu­ba­tor can be arranged indi­vid­u­al­ly for dif­fer­ent micro­scop­ic appli­ca­tions and acces­sories with var­i­ous slide-in mod­ules. To the prod­uct