Incubator NL Ti2 BLACK 2000

Incubator NL Ti2 BLACK 2000

This new light-tight incu­ba­tor has been devel­oped for the invert­ed micros­cope Nikon Eclipse Ti2-E (a vari­ant for usage with Stage Up Kit is avail­able). Con­struct­ed from black acrylic glass the incu­ba­tor enclos­es the micros­cope, the nose­piece, the objec­tives and fur­ther com­po­nents and is used to enable a con­trolled warm air incubation. 


  • Large incu­ba­tor for the invert­ed micros­cope Nikon Eclipse Ti2-E (a vari­ant for usage with Stage Up Kit is avail­able) for warm air incu­ba­tion and CO2/O2 control
  • Easy attache­ment to the micros­cope in a few sim­ple steps
  • Silicone-sealed open­ings for the feed-through of cables with­out the need to dis­con­nect them
  • Black cas­ing mate­r­i­al for micro­scop­ic tech­niques in which scat­tered light is dis­turb­ing, e.g. flu­o­res­cence microscopy
  • Two large black slid­ing doors at the front of the incu­ba­tor on the left and right hand side
  • A mov­able obser­va­tion win­dow behind the front slid­ing doors enables the incu­ba­tion appli­ca­tion to be mon­i­tored with­out heat loss. This win­dow can be pushed com­plete­ly to the left, allow­ing an easy access to the inside of the incubator.
  • Two slide-in mod­ules are avail­able; the left one with a silicone-sealed open­ing for cables and hoses
  • Equipped with an inte­ri­or light­ing that con­sists of an LED bar on the front inside and an on/off switch on the top right of the incubator
  • One-piece tem­per­a­ture sen­sor cable that is adjustable in length and does not have to be plugged into the incu­ba­tor => lower risk of damage
  • New design: the lamp sup­port seal­ing can be swiveled back over the lamp sup­port and the attached fil­ter slider
  • Hold­er for the 250 ml Humid­i­fi­ca­tion Bot­tle on the inner left side of the incubator
  • Homoge­nous heat dis­tri­b­u­tion in the obser­va­tion area by a con­cen­tric air sup­ply from the rear
  • For oper­a­tion, other heat­ed or non-heated com­po­nents are recommend
  • For spe­cial appli­ca­tions (e.g. mul­ti­well plates with glass bot­toms) the incu­ba­tor can be oper­at­ed with the Heat­ing Unit alone
  • Local CO2 and O2 gassing with the suit­able components


Material acrylic glass (PMMA), black
Valid temperature range 10°C – 50°C
Temperature sensor Pt100
Efficiency of power supply VI
Internal dimensions (WxHxD)
688 x 416 x 274 mm
Opening sliding door left (LxW) 150 x 160 (mm)
Opening sliding door right (LxW) 150 x 160 (mm)
Opening sliding door in the right-hand adapter (LxW) 170 x 70 (mm)
Weight (incubator with slide-in modules) approx. 9.3 kg
Incubator NL Ti2 BLACK 2000


  • Nikon Eclipse Ti2-E with mechanical stage or scanning stage
  • Nikon Eclipse Ti2-E with Stage Up Kit (TI2-LA-SU) and mechanical stage or scanning stage

Compatible PeCon Products:

A selection of compatible heatable components: Components additionally needed for CO2 and O2 control:

Application Examples: