PeCon Series 2000 Firmware

Get the lat­est firmware for our Series 2000 devices and com­po­nents to have new fea­tures, bug­fix­es and full com­pat­i­bil­i­ty of all devices with each other.
To the downloads

CO2-Controller 2000

The CO2-Con­troller 2000 is a con­trol unit used for the pressure-less sup­ply of small incu­ba­tors on micro­scopes with a con­trolled CO2 air mix­ture via small gas feed­ing. With the use of cheap tech­ni­cal CO2 a con­trolled gas mix­ture from 0.0-20.0% CO2 can be gen­er­at­ed. A Humid­i­fi­er flask is included.
To the product

CO2-O2-Controller 2000

The CO2-O2-Con­troller 2000 is a con­trol unit for the pressure-less sup­ply of small incu­ba­tors on micro­scopes with a con­trolled CO2/O2 air mix­ture via small gas feed­ing. With the use of cheap tech­ni­cal CO2 and N2 a con­trolled gas mix­ture from 0.0-20.0% CO2 and 20.8% - 0.1% O2 can be gen­er­at­ed. Long last­ing zir­co­ni­um based oxy­gen sen­sor. A large Humid­i­fi­er flask is included.
To the product

Incubator NL 2000 for dual level construction

Large incu­ba­tor for the invert­ed micros­cope Nikon Eclipse Ti with dual level con­struc­tion for warm air incu­ba­tion and CO2-con­trol. Local CO2-incu­ba­tion can be car­ried out with the CO2-Con­troller in com­bi­na­tion with appro­pri­ate CO2-Covers. The large inter­nal vol­ume allows the use of many dif­fer­ent components.
To the product

Incubator HF 2000 with Heatable Glass

The Incu­ba­tor HF 2000 is designed to fit onto the Heat­ing Frame 2000 and per­mits a local CO2-and tem­per­a­ture con­trol of Petri dish­es and POC-chamber sys­tems in a com­plete­ly closed envi­ron­ment. The cover has a rec­tan­gu­lar obser­va­tion win­dow with heat­able glass.
To the product

Setup K

The Setup K has been devel­oped for per­fu­sion appli­ca­tions in com­bi­na­tion with the
Uni­ver­sal Mount­ing Frame KP-Set, the Uni­ver­sal Mount­ing Frame KP-Set lock­able, or the Uni­ver­sal Mount­ing Frame K100-Set. Per­fu­sion tubes and thin cables can be eas­i­ly led into the inte­ri­or of the Setup through six sil­i­cone sealed openings.
To the product

CO2-Cover 100-Set

The CO2-Cover 100-Set fits on the Uni­ver­sal Mount­ing Frame K100-Set and M100-Set on invert­ed micro­scopes. It per­mits a local CO2-con­trol and humid­i­fi­ca­tion in a com­plete­ly closed envi­ron­ment. Usage in a large incu­ba­tor is high­ly rec­om­mend­ed to pre­vent condensation.
To the product

Universal Mounting Frame K100 protected

Flex­i­ble device for the fix­a­tion of var­i­ous cul­ti­va­tion ves­sels and T25 flasks on mechan­i­cal and scan­ning stages (open­ing 160x110 mm) at inverse micro­scopes. It has been specif­i­cal­ly designed for the use of large Petri dish­es with a max­i­mum diam­e­ter of 92 mm and can be installed easily.
To the product

Universal Mounting Frame K100 Set

Uni­ver­sal Mount­ing Frame with 5 base­plates for ‘35’,’60′ and ‘100’ Petri dish­es, POC-Systems, Lab-TekTM and Ibidi Cham­bers. The frame fixes var­i­ous cell cul­ti­va­tion ves­sels on scan­ning and mechan­i­cal stages (open­ing 160x110 mm) on invert­ed micro­scopes and can be installed eas­i­ly. The base­plates togeth­er with the CO2-Cover 100-Set give a closed envi­ron­ment inside a large heat­ed micros­cope incu­ba­tor for local gassing and humidification.
To the product

Heating Insert UP-Set 2000

The Heat­ing Insert UP-Set 2000 is designed for the sta­ble heat­ing of cell cul­ti­va­tion sys­tems on upright micro­scopes above ambi­ent tem­per­a­ture up to 60°C. It can be equipped with a CO2-Cover for local CO2 con­trol and humid­i­fi­ca­tion. Because of its solid design, it has a high tem­per­a­ture con­stan­cy and ther­mal con­duc­tiv­i­ty. Four exchange­able base­plates enable the use of a large num­ber of cell cul­ture systems.
To the product